Description: STORE HOME ALL ITEMS ABOUT US ADD TO FAVS FEEDBACK CONTACT US 2Pcs Oxygen O2 sensor 1 & 2 for 04-07 2008 2009 Toyota Prius 1.5L Upper+Lower NOTE: Please make sure your original OE number and plugs are the same as our products before purchase. Description: Condition:100% Brand New And High Quality Manufacturer Part Number: 234-4209,89465-47070,89467-47071 Position: Upstream&Downstream Color: As the pictures show Fitment Type : Direct Replacement Easy to install Fitment For: For 2004-2009 Toyota Prius 1.5L Package Include: 2x O2 Oxygen Sensors AS the Pictures Shown Must Know Before Buying: The following information is for instructional and guidance reference only. We try and make them as accurate as we can.If Check Engine Light is on or an OBDII Trouble/Fault code occurs after installation, check the sensor with a voltmeter as below. If the sensor is good, further diagnosis is required. There're many different codes for specific functional failures, which are NOT necessarily relevant to the sensor. Find out what the Code means before leaving any feedbacks. Items that have been installed, altered or contaminated are non-returnable. ONLY a defective sensor after tested by a voltmeter is applied to manufacturer warranty. 20% restocking fee is required if buyer bought wrong items due to not paying attention to fitment information and ask for return. The Price, Quality & Funcitonality of the O2 Sensor is fully covered under our warranty & return policy. However, refund for any labor cost, expense in a dealer shop or damage due to wrong installation is NOT covered. Q: How do I know the O2 sensor is good or not? (Online Video) A: The only way to know if the O2 sensor is functioning normally is to check its responsiveness to changes in the air/fuel mixture, by Voltage Measurement or Waveform Simulation. Use a 10-megaohm digital voltmeter. Hook up the voltmeter's red probe to the sensor's signal wire and the black probe to engine ground. (Use back probe method, DO NOT pierce the wire.) For a good sensor, voltage should fluctuate constantly between 0.1 and 0.9 volts after starting the engine for 2 or 3 minutes. Please take a video clip of the voltmeter and contact us if our sensor: Goes above range between 0.1 and 0.9 volt Remains below 0.5 volts Stays fixed at a particular voltage You're free to choose replacement or refund if our sensor fails to work, in this case. Q:Why does the oxygen sensor have false alarm, after installation ? A: The clearing of the errors can be obtained on most systems when the vehicle battery is disconnected for at least 60 seconds. The assignment of the new sensor parameters is done automatically when the errors are cleared, but in some systems a short adapting tour is required. In this case the vehicle has to be driven on the road for some 10-15 minutes, in order to have the ECU adapt itself to the new sensor. Q:How should I install oxygen sensor ? A: The following is the installation instructions: Use the correct part number as listed in the application catalogue ,Do not use sensor if i has been dropped ,Remove protection cap just prior to installation; Firstly install sensor body ensuring lead wire is not twisted or bent , Do not use impact wrench or socket type wrench to install sensor ,M18 sensors - install finger tight then 1/2-3/4 turn with a wrench (35-45Nm) ; Then connect and route lead wire as originally installed , Do not allow lead wire to touch exhaust manifold or any other hot component ,Do not apply any substances (especially oil or grease) to connector sensor ,Do not use leaded fuels,silicone or metal based additives. Q:When should replace the oxygen sensor? A:Oxygen Sensor Failure Symptoms: Reduced fuel mileage Failed emissions testing A check engine light Poor drive-ability SKU: CP.LM.227 Shipping Weight: 8 oz 2- Padded FR Envelope 3- Regional Box A PAYMENT PayPal Preferred. Local pickup NOT available at this time. SHIPPING We process your order within 1 business day upon payment(note: NOT counting holidays or weekends). International shipping also available, please note by default most of the international packages shipped out by USPS First Class Mail Intl only have limited tracking update while the package was in US. Package transit time: please expect 3-5 business days within US, 5-10 business days to Canada, up to 20 business days all around the world. RETURNS Please read the item description and check the pictures carefully before bidding. Return or refund is available only ifitem DOA or there's error in item description causing the item not fitting your need. In such cases, seller pays for all related shipping cost if any. Returns are also acceptable if buyer purchased this by mistake and item still in good condition for reselling. Buyer is responsible for all related shipping cost. Copyright © 2023 wfxpress. All Rights Reserved.
Price: 40.99 USD
Location: San Diego, California
End Time: 2024-10-04T08:40:51.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Return shipping will be paid by: Seller
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
Brand: wfxpress
Type: Sensor
Interchange Part Number: for 234-4209
Sensor Type: Oxygen Sensor
Manufacturer Part Number: for 234-4209
Interchange Part Number 2: For 89465-47070, 89467-47071
Interchange Part Number 1: For 8946547070, 8946747071