Armor WB25 Water Based High Gloss Acrylic Sealer

Description: The Armor WB25 is a water-based acrylic cure and seal designed to enhance, seal, and protect concrete and paver surfaces. It will protect the surface with a durable high gloss surface film. The Armor WB25 is a fantastic sealer if you are looking to enhance surfaces with a high gloss finish. The Armor WB25 also doubles as a cure and seal and can be applied to new concrete.The Armor WB25 is made from high quality, non-recycled, US manufactured resins. It is non-yellowing, breathable, and low VOC. The protective high gloss film will reduce damage and deterioration caused by surface abrasion and water absorption including cracking, spalling, pitting, dusting, and the growth of mold, mildew, and algae.Benefits:Meets ASTM 1315 and ASTM C 309 standardsProtective surface film will reduce damage and deterioration caused by water absorption and surface abrasionProtective surface film will reduce the growth of mold, mildew, and algae on the surfaceMade from non-recycled US manufactured resinsEasy to apply, easy to maintain, easy to re-coatUV resistant, breathableUses:The Armor WB25 is a great choice for a variety of interior and exterior concrete applications, including:Pool decks and patiosDriveways, walkways, and stairsGarage and basement floorsRetail and shop floorsWarehouse floorsMuch more!The WB25 can be applied to a variety of interior and exterior concrete surfaces, including:Stamped concretePoured and broom finished concreteExposed aggregate concreteConcrete paversNew, uncured concreteThe Armor WB25 is designed specifically to be used on unsealed concrete and concrete pavers. It can also be applied to concrete and concrete paver surfaces previously sealed with a water based acrylic as long as the acrylic has been properly prepped for adhesion. The Armor WB25 should not be used to seal clay brick, red Chicago pavers, flagstone, slate, or natural stone. If you are looking to seal clay brick, red Chicago pavers, flagstone, slate, or natural stone, consider instead of the Armor WL550 or the Armor SX5000 WB.The Armor WB25 can’t be applied over any other film forming sealer, other than a water-based acrylic sealer. It can’t be applied over a water based acrylic, an acrylic latex, a paint, epoxy, or urethane.AppearanceWhen applied in clear, the Armor WB25 will provide a transparent high gloss finish.The actual level of gloss and enhancement received will depend on the type and age of the surface, age, porosity, condition, applicator, application method, and amount of material applied. For an accurate representation of what your surface will look like once sealed, we suggest applying the product to a test area first.Product LifeWhen properly applied, the Armor WB25 can provide up to 1-3 years of life on an exterior surface before the need to recoat, and up to 2-7 years of life on an interior surface.While the Armor WB25 is designed to out-last and out-perform similar products on the market, there are several factors that can impact actual product life including the severity of surface abrasion and level of foot traffic, the porosity of the concrete or pavers, and the amount of resin build-up on the surface. Some surfaces need to be sealed every year, while others can go a few years without sealing. How To Apply:The Armor WB25 can be applied with a 3/8-1/2” nap roller, or an HVLP sprayer. For a consistent high gloss finish, apply two coats spaced 6-8 hours apart. Do not exceed 24 hours apart between coats.Time Of DayThe Armor WB25 should only be applied in the early evening (around 5 PM or later) when air and surface temperatures are declining, and when the sun is no longer positioned over the surface.Surface PreparationThe Armor WB25 should be applied to a completely clean and dry surface. If the surface was cleaned with water or pressure washed prior to application, allow the surface to dry for at least 24 hours before sealing. While the surface may appear dry and feel dry to touch, water below the surface trapped in the pores can cause the same issues. While pressure washing the surface is typically sufficient, spot treatment may be necessary for deep or older stains.The Armor WB25 is designed specifically for use on unsealed concrete and concrete paver surfaces, as well as concrete and concrete pavers previously sealed with a water based acrylic. Do not apply this product over a surface previously sealed with a solvent based acrylic, or any other type of film-forming sealer. If the surface is smooth troweled, or does not easily accept water, acid etching may be required prior to applying sealer. It is always suggested to apply the Armor WB25 to a test area to verify absorption, coverage, compatibility, and project suitability.Note About Sealing Pavers:Please note, the Armor WB25 is not a bonding agent. Do not apply the Armor WB25 over loose sand between paver joints because it will not harden or seal the loose sand. The Armor WB25 can be applied over the pavers directly, or the pavers and polymeric sand (if the polymeric sand is newly installed, wait 7 days before sealing), but it can’t and should not be applied over loose sand.Adding Non-Slip: For best results, apply the Armor non-slip additive with an appropriate hand-held broadcast spreader. When applying the second coat, add the non-slip additive to the coating using a broadcast spreader, and back roll to encapsulate the non-slip additive.For complete application instructions and safety data, please refer to the Technical Data Sheet and SDS Sheet. Coverage:Porous Surfaces: Up to 175 FT2/gallon in one coat.Smooth Surfaces (once properly prepped): Up to 200-225 FT2/gallon in one coat.Coverage will vary depending on porosity, surface condition, application method, and the amount of material applied by the applicator. The above coverage rates are estimates and will vary. Two coats are suggested for even coverage and appearance.

Price: 64.99 USD

Location: Amherst, New Hampshire

End Time: 2024-01-17T13:08:37.000Z

Shipping Cost: 0 USD