Bellm No3 Spring Kit Thompson Center Arms Encore ProHunter Endeavor FX Trigger

Description: Bellm No.3 Spring Kit Thompson Center Arms Encore ProHunter Endeavor FX Trigger Job spring kit. This is our MOST POPULAR and requested kit, 10:1 any other. Do IT YOURSELF Upgrade your TC Encore's performance with a Bellm Custom Spring Kit. This auction includes a #3 Bellm Custom Trigger/Sear Spring, a Bellm Custom 44# "Speedlock" Hammer Spring, Bellm Custom Heavy Duty Locking Bolt Spring for the barrel, Bellm Heavy Duty FIRING PIN return spring, Encore Trigger guard Spring. This 6 Spring kit addresses these issues: 1) A tighter lockup by applying more force to the barrel's locking bolts. 2) #3 trigger/sear spring for a lighter trigger pull weight, approximate 2 1/2 to 3 lbs pull. 3) Our much stronger 44# "Speedlock" hammer spring for noticable ignition difference. 4) Heavy Duty Firing pin return spring prevents broken firing pins, tool steel firing pins sold separately. 5) Bellm Encore, Pro Hunter, Endeavor, FX Trigger guard return spring. 6) NEW! Bellm Trigger Plunger return spring As described on the Heavy Duty Locking Bolt Spring page, the top surfaces of the locking bolts are on a slight angle. Thus more force to the locking bolts ensures a tighter lockup. This is especially important in Encore barrels which have: 1) A larger surface area on the locking bolts, 2) Far greater forces applied to the locking bolts from both the weight, and thus leverage, of the heavier Encore barrels and the far greater forces exerted from much higher intensity rounds than fired in the Contender or G2, YET... 3) The Encore uses the same exact factory issue locking bolt spring as the Contender & G2. Available choices of Bellm Custom Trigger/Sear Spring #1, #2, #3, in the weight range that is normally just a "drop-in" installation for novices and experienced gunsmiths alike. Sear Springs #4,#5,#6,#7 generally require modifying the sear notch. Installation of the Heavy Duty Locking Bolt Spring requires a common 3/32" ROLL pin punch, listed in the Tools section if you do not already have one, to knock out the "roll pin" or "spring pin" that retains the locking bolts in the barrel lug. After installation of the Heavy Duty Locking Bolt Spring, push the locking bolts in all the way and make certain the rear most end of the locking bolts is at least flush with the end of the barrel lug. Once in awhile a locking bolt spring hole is drilled a bit shallow, and the spring will compress all the way before the locking bolts are pushed back into the lug far enough to completely clear the inside of the frame during closing the barrel. If the locking bolts cannot be pushed in completely flush with the end of the barrel, cut or grind off one end of the spring about 1/2 coil at a time until the locking bolts can be pushed in all the way. Also, if you want a stronger lockup than the factory spring gives, but opening the barrel with an unaltered Heavy Duty Locking Bolt Spring requires more effort than you are comfortable with, you can shorten the spring some to make opening the barrel easier. Adjust its tension to suit your needs. After installing the Bellm Custom Trigger/Sear Spring it is imperative that you perform the safety function checks detailed in our Encore Trigger Job Instructions available in separate auction. The G2 is slightly different, but functionally the same as the Encore, so these instructions for the Encore apply to the G2 as well. We also recommend you order our Encore & G2 Trigger Job Instructions printed shop manual found in the menu bar to the left here on the online store. It points out the distinctions between the Encore and G2 and has updates not in the free download. In short, the hammer must be securely cocked and not readily pushed off with moderate thumb pressure, and the hammer must rebound to half cock when you remove your finger from the trigger. If the frame fails to pass either or both of these safety tests, corrective action MUST be taken before continuing to use the frame. Our Trigger/Sear Spring Installation Pliers, listed in the menu to the left, are highly recommended not only for the initial installation of the Trigger/Sear Spring, but for reassembling the frame after routine cleaning. They keep the spring captive and make installation quite easy. Why install our "SPEEDLOCK" hammer spring? If you observe correct size die adjustment and maintain the recommended minimum headspace as described on the Bellm Headspace Indicator page linked from the menu bar to the left, and have cut only a very small amount from your hammer spring to get reliable rebounding of the hammer, the 44 pound hammer spring is a must have. If you shoot just factory ammo or military ammo and have been getting misfires, you should definitely choose use the 51 pound spring, especially if it is related to excess headspace. Note that installing a heavier hammer spring tends to produce a somewhat lighter pull weight due to the design of the sear and hammer mechanism. The hammer spring can be installed in one of two ways, either after fully disassembling the frame or by simply unscrewing the hex nut that the grip or buttstock screw goes into. Remove this nut, and the hammer spring and its strut drop out. After installation of the hammer spring you MUST verify that the hammer rebounds back to half cock every time you lower the hammer and remove your finger from the trigger. If it does not rebound to half cock, cut off a little at a time until the hammer will rebound to half cock every time. There should be about .2" of free travel of the hammer at its forward end of the stroke where there is no tension on it from the hammer spring. One of the main reasons for the "Speedlock" Hammer Springs is to maintain as strong or stronger hammer fall after reducing the trigger pull weight and often having to shorten the issue hammer spring so it will let the hammer rebound to half cock. Since we have no control over whether you read the instructions we give or how you perceive the instructions, users of any of these springs assume all liability for the results they obtain. Refer to: bellmtcs.com/store/index.php?cid=86=0 for full description of our custom hammer springs. Note that we do not offer trigger/sear springs lighter than #4 in these "drop-in" kits since going to a lighter trigger/sear spring often requires altering the angle of the sear notch, work reserved for the more experienced do-it-yourselfers and bonafide gunsmiths who understand this type of work. FULL TECH support, phone or email Tip: Print this page out so you have the disassembly/reassembly sequence and safety function checks handy. No printed detailed instructions come with the springs or pliers. Purchase our Bellm Trigger Job Instruction Manual Separate. Mike Bellm's TCs has been serving the TC shooting community for over 30 years, you are buying from the trusted TC Encore and Contender expert. Small parts orders and other auctions can be combined shipping, your Bellm parts will be packaged by the Pros. DISCLAIMER and WARNING! You must be 18 years of age or older to purchase this product. We advise that all BELLM TCs LLC products be installed and/or inspected after installation by a qualified gunsmith. Modifying sear and engagement surfaces are done at your own risk and we highly recommend that you DO NOT modify, hone or polish any sear or engagement surfaces with anything but the BELLM TCs LLC sear hone and polishing stones and only follow the BELLM TCs LLC instructions. Reducing trigger pull weight below 1.5 lbs of pull is NOT recommended due to the manufactures design, there is a chance that dropping the firearm with the hammer cocked or pushing on the hammer with moderate force could cause a discharge at ANY reduced pull weight. It is your responsibility to inform, educate, and warn anyone using your modified weapon as to it's design, function, and its unique and safe handling. Before installing check with all STATE and FEDERAL laws, there may be a law that prohibits you from modifying your firearm and it is up to you to know these laws and abide by them. By ordering and installing this product or any BELLM TCs LLC product you agree to take FULL RESPONSIBILITY for any and all legal, health, and warranty issues that may occur and you agree to hold BELLM TCs LLC harmless for anything that may occur from the use or installation of this product.

Price: 29 USD

Location: Olathe, Colorado

End Time: 2024-01-13T05:51:21.000Z

Shipping Cost: 0 USD