Description: This item is pre-owned – it will work like new once programmed to your vehicle One (1) Aftermarket remote keyless entry fob alarm Transmitter control clicker keyfob controller replacement Functions at 100% Tested & Guaranteed Omega / Excalibur / K-9 / Crimeguard / Freedom / Executive / Python FCC ID: H5LAL789D Part #: AU-3T Circuit board #: 789D Interchangeable circuit board #s: 789D 789E Frequency: 302 – 304 MHz LED color: Red 2 buttons Battery: (1) 23A Compatible with the following systems CG 5000 CG 5000F CG 5000-L CG 5000in CG 7000 CG 7000in CG 9000 AL-532 AL-532-L AL-532-F AL-632 AL-632-L AL-732-LC AL-770 AL-770GT AL-770-L AL-770LC AL-790 AL-790D AL-832 AL-700EX AL-700EZ AL-700GT AL-800 AL-900ATX AL-900ATZ AL-900GTX K9-FIVE K9-FIVE-F K9-FIVE-L K9-SEVEN K9-SEVEN-GT K9-SEVEN-L K9-SEVEN-LC K9-SIX K9-SIX-CP K9-SIX-DIP K9-SIX-L M.A.T.-5 M.A.T.-5F M.A.T.-5L M.A.T.-6 M.A.T.-6 DIP M.A.T.-6L M.A.T.-7L M.A.T.-7EX M.A.T.-7EZ M.A.T.-7LC M.A.T.-8 M.A.T.-9ATX M.A.T.-9ATZ M.A.T.-9GT M.A.T.-9LCX AU-REC-1 AU-REC-1LC AU-REC-2 AU-REC-2LC IN-5000 IN-7000 Programming Instructions: METHOD # 1 Before you begin, your system must be in a disarmed state and you must know where your valet switch is located. If you are unfamiliar with your valet switch, click here. If you know where your valet switch is, perform the following steps: 1) Turn the vehicle's ignition to the "on" position 2) Within 7 seconds of step 1, press the valet switch 5 times. The alarm should respond with a long siren chirp. 3) Press the large/ lock button on your remote (for Freedom 500, C-5, and K9 Mundial2, press 2nd or 3rd channel. For MARS-22, press Lock & Unlock at the same time). The alarm should respond with a short siren chirp. 4) Repeat step 3 for each additional remote that is to operate the system (up to 4 remotes). Note: the system will automatically exit programming mode if it detects a 15 second period of no activity. METHOD # 2 Before you begin, your system must be in a disarmed state and you must know where your valet switch is located. If you are unfamiliar with your valet switch, click here. If you know where your valet switch is, perform the following steps: 1) Turn the vehicle's ignition to the "on" position 2) Within 7 seconds of step 1, press the valet switch 5 times. The alarm should respond with a long siren chirp. One Button Remote: 3) Press the button on your remote. The alarm should respond with a short siren chirp. 4) Press the valet switch one time. 5) Proceed to step 6. Two button remote: 3) Press the large button on our remote. The alarm should respond with a short siren chirp. 4) Press both buttons at the same time. The alarm should respond with 2 short siren chirps 5) Press the small button on your remote. The alarm should respond with 3 short siren chirps. Three button remote: 3) Press the large button on your remote. The alarm should respond with a short siren chirp. 4) Press the small right button on your remote. The alarm should respond with 2 short siren chirps. 5) Press the small left button on your remote. The alarm should respond with 3 short siren chirps. 6) Repeat steps 3-5 for each additional remote that you wish to operate your system (up to 4 remotes). Note: the system will automatically exit programming mode if it detects a 15 second period of no activity. METHOD # 3 Before you begin, your system must be in a disarmed state and you must know where your valet switch is located. If you are unfamiliar with your valet switch, click here. If you know where your valet switch is, perform the following steps: 1) Turn the vehicle's ignition to the "on" position 2) Within 7 seconds of step 1, press the valet switch 5 times. The alarm should respond with a long siren chirp. 3) Press the valet switch to enter your secret override code. If a code has never been programmed, press the valet switch one time. The alarm should respond with a long siren chirp. 4) Press the large/ lock button on your remote. The alarm should respond with a short siren chirp. 5) Repeat step 4 for each additional remote that is to operate the system (up to 4 remotes). Note: the system will automatically exit programming mode if it detects a 15 second period of no activity. METHOD # 4 Before you begin, your system must be in a disarmed state. Perform the following steps: 1) Turn the vehicle's ignition from "off" to "on" 5 times within 7 seconds. The system should respond with a horn honk or the doorlocks will lock then unlock. 2) Press the large/ lock button on your remote. The system should respond with a short horn honk or the doorlocks will lock then unlock. 3) Repeat step 2 for each additional remote that is to operate the system (up to 4 remotes). Note: the system will automatically exit programming mode if it detects a 15 second period of no activity. METHOD # 5 This type of alarm automatically enters transmitter programming mode upon power up. Before you begin, make sure that all points of entry (doors, trunk, hood) are closed. If there is a hood pin switch, have a friend hold it down or temporarily disconnect it. The system will not enter programming mode if it detects an open point of entry. Perform the following steps: If the system has been without power for more than 24 hours: 1) Apply power to the system. 2) Press the large/ lock button (Press small center button for Freedom 400) on your remote. The system should respond with a short siren chirp. 3) Repeat step 2 for each additional remote that is to operate the system. If the system has had power within the last 24 hours: 1) Disconnect and re-apply power. 2) Press the large button (Press small center button for Freedom 400) on any remote that does not already operate the system (this is how the system determines that you want to program transmitters). The system should respond with a short siren chirp. 3) Repeat step 2 for each additional remote that is to operate the system. Note: the system will automatically exit programming mode if it detects a 15 second period of no activity. METHOD # 6 Before you begin, your system must be in a disarmed state and you must know where your valet switch is located. If you are unfamiliar with your valet switch, click here. If you know where your valet switch is, perform the following steps: 1) Turn the vehicle's ignition "on" then "off". 2) Within 7 seconds of step 1, press the valet switch 5 times. The alarm should respond with a long siren chirp. 3) Press the valet switch one time to enter transmitter programming mode. 4) Press the large/ lock button on your remote. The alarm should respond with a short siren chirp. 5) Repeat step 4 for each additional remote that is to operate the system (up to 4 remotes). Note: the system will automatically exit programming mode if it detects a 15 second period of no activity. METHOD # 7 Transmitters for this model alarm are coded from the factory. The transmitter has to be modified to match the code of your alarm. If you need a replacement transmitter for your alarm, you will need to open the transmitter shell (there is typically a small phillips head screw in the back that must be removed first). You will need to look on the circuit board for a white paper sticker that has a 5 or 6 digit code that will start with 1, 2, or 3. You will need to provide this code to your dealer or Omega at the time of purchasing the transmitter so it can be precoded to operate your alarm. 100% Guarantee Remote Shipping / Return Policy We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged. Please Note: Each remote and circuit board is UV id’d prior to shipment – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement. Does this keyless remote entry come with a battery? Yes. It will have a working battery installed. Battery Condition: A. All remotes sold on Keyless4u include working batteries. B. Installed batteries are not tested for battery life- they are simply working. Some are new and some are used. Your vehicle will be installed with one of the following keyless entry systems: a. Standard Keyless Remote Packages: Installed at time of manufacture. b. Optional Keyless Remote Packages: Installed by a dealer. c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop. d. No remote keyless entry system at all. The above information can change which remote you need for your installed remote keyless system.
Price: 22.89 USD
Location: Wellsboro, Pennsylvania
End Time: 2024-10-26T15:25:57.000Z
Shipping Cost: 6.96 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Seller
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
Manufacturer Part Number: H5LAL789D
Interchange Part Number: K9-SIX K9-SIX-CP AL-770GT AL-770-L AU-REC-2LC
Other Part Number: STOCK 758 SEVEN-GT 900ATZ 789D 789E 302Mhz AU-3T
Surface Finish: 2 BUTTONS RED LED LIGHT
Warranty: 30 day
Brand: Aftermarket Products
Part Brand: K9 OMEGA EXCALIBUR CRIMEGUARD EXECUTIVE
programming required: see listing description for details
Country/Region of Manufacture: Unknown
Type: Wireless
Color: Black
Features: keyelss remote entry fob