Planet Audio PL1500.1M Pulse Series Car Audio Amplifier

Description: Style and SoundFeel the beat with the Planet Audio Pulse PL1500.1M Class A/B Monoblock Amplifier. With 1500 Watts Max Power and MOSFET power supply, this Amplifier gets your music in gear.Customize the sound with Variable Low Pass Crossover, Switchable Bass Boost and Remote Subwoofer Control.When space is limited but your passion for great sound is not, Pulse Amplifiers with blue illuminated end panel strips and logo, are just what the doctor ordered to power up your music and get your heartbeat racing.Class A/B, Monoblock, MOSFET power supply1500 Watts @2-Ohms x 1 Max, 750 Watts @4-Ohms x 1 MaxHigh and low level inputs, Thermal overload speaker and short protectionPower and protection LEDs, Variable low pass crossover, Switchable Bass BoostCrossover Switch, Variable input gain control, Input Sensitivity SelectorTHD @ RMS output: 0.01%, S/N Ratio: 103 dB, Frequency: 9 Hz – 250 KHzDimensions: 9.96” x 7.00” x 2.39”, Weight: 5.1 lbs.Remote Subwoofer ControlMOSFET Power SupplyMetal Oxide Semiconductor Field-Effect Transistors quickly switch from full to non-conduction for high-efficiency output.Class A/BOur Class-A/B amplifiers feature specific linear circuitry that increases sound quality and power output while reducing distortion and improving efficiency.2 Ohm Stable2-Ohm stable comfortably powers speakers or subwoofers when in use at 2-Ohms, resulting in more power and volume.High and Low Level InputsHigh-level inputs accept speaker output signals and low-level inputs accept pre-amp output signals to allow for the addition of amps and processors to standard factory or aftermarket source units.Variable Low Pass FilterVariable low-pass filter gives you control over the frequencies that pass through to the subwoofer.Switchable Bass BoostSwitchable Bass Boost allows you to boost the low bass +18db.Variable Input ControlThe Variable Input Control allows the amplifier input to match the output signal from the head unit to achieve optimum performance when adjusted properly.Switchable Input SensitivitySwitchable input sensitivity provides adjustable control over the input signal from the head unit to achieve customized balance between power and sound quality.Power Input TerminalsWhen installing all Planet Audio amplifiers, it is important to use the MAXIMUM gauge of wire that the power terminals will accommodate. For instance, if an amplifier has 4 gauge power and ground terminals, use high quality 4 gauge multi-strand copper wire to make your power connections. This maximizes the amplifier’s ability to draw the required power upon demand. This also helps prevent overheating that could cause failure. ALWAYS make sure your vehicle’s electrical system is capable of handling the current demands from any after-market accessory.Please refer to the amplifier’s owner’s manual for correct wire gauge sizes.FusesFuses protect BOTH the amplifier and the electrical system of your vehicle from faulty conditions.If you must replace a fuse on the amplifier, always use a fuse of exactly the same type and rating of the one you are replacing. A different type of fuse or rating may result in damage or cause a fire. Please refer to your owner’s manual for reference on fuse size and type.If you plan on using multiple amplifiers in your system, be certain that you have the appropriately sized gauge wire to accommodate the current demands for all amplifiers and that the wire is fused correctly at the battery. Connect an empty fuse holder within 18" (45 cm) of the car battery and run a 4 gauge (or heavier) cable from this fuse to the amplifier location. A fused distribution block is recommended when using several amplifiers or accessories.Proper GroundingProper grounding is essential for any electric accessory in a vehicle.Some key points to remember: Keep the ground as short as possible. Connect the amplifier’s power ground terminal to the closest point on the chassis of the car. Keep this ground wire to less than 39" (100 cm) in length. Use 4 gauge (or heavier) wire. Scrape any paint away, use a star washer to “bite” into the metal and secure it tightly using a grounding lug.Any steps that aren’t followed properly will result in a higher resistance at the ground point, causing unnecessary heat, high current draw, and potentially damaging the electrical accessories in the vehicle.InstallationPlease be advised that “Professional” installation of all of our products is recommended and encouraged. Installation by a professional installer increases the length of any applicable assurance on most Boss Audio Systems products. The manufacture certificate of assurance is void, however, on product that is damaged during installation by a non-professional installer. Professional installation should also ensure trouble-free usage for

Price: 75.99 USD

Location: Oxnard, California

End Time: 2023-09-24T23:22:20.000Z

Shipping Cost: N/A USD