VIPER KEYLESS remote ALARM key FOB TRANSMITTER EZSDEI474V CE0890 EUC car starter

Description: One (1) Aftermarket remote keyless entry fob alarm Transmitter control clicker keyfob controller replacement Functions at 100% Tested & Guaranteed Directed Electronics Inc. (DEI) Viper FCC ID: EZSDEI474V ( Alternate Spelling: EZSDE1474V ) Interchangeable FCC IDs: EZSDEI474 EZSDEI474V Part #: 474V Interchangeable Part #s: 470 474 475 476 485 820041 7143 26131 SAA474U Circuit board # DTGB Frequency: 433 - 434 MHz (433.92) LED color: Green 4 buttons Please note: A Valet / Programming switch is required to program this remote. Programming can be difficult if you are not familiar with it. Please read the programming instructions (below) before purchasing. Assistance from an auto specialty shop or locksmith may be needed. Compatible w/ the following systems: Automate 6 7 10 25 35 410 425 435 52 53 552 553 Avital 2100 2200 2300 3100 3200 3300 4000 4100 4200 4300 4400 Maxx2 Maxx3 Hornet 533 T 554 T 740 T 742 T 851 T Python 400 HP 440 HP 450 ESP 460 HP 500 HP 625 HF 650 ESP 660 XP 700 900 1000 HF PC 1000 HF 1200 XP 1400 XP 1500 HF 1600 XP 2000 HF 3000 HF 3000 ESP Sidewinder 3000 HF 3000 ESP 3200 HS 3300 HS 3500 ESP 4500 HF 5000 HF 5000 ESP 5500 XS 6000 HF 6000 ESP 6500 HF 6500 ESP 7000 HF 7000 ESP PC 7000 SHF Rattler 100 110 D 200 210 D 250 259 R 300 310 D 359 R 369 D Valet 450 R 519 H 551 R 552 T 562 T 561 R 712 T 716 T Merlin 2000 Ungo K10 K20 RK1 RS10 S100 S400 S660 S670 SR1000 SR5000 SR6000 Viper 100 HF (ESP) 130 HV 150 ESP 160 XV 210 HV 211 HV 300 HF PC 300 HF (ESP) 300+ HF 330 V 350 HV 500 HF PC 500 HF (ESP) 550 HF 550 HF (ESP) 560 XV 571 XV 600 HF PC 600 HF (ESP) 650 XV 671 XV 700 ESP 771 XV PC 800 SHF 800 SHF ESP 850 XV 1000 1002 3000 3002 5000 5002 7900 Programming Instructions: The vehicle’s system can store up to 4 transmitters (remotes) into memory. Use the following programming routine to add transmitters to the vehicle’s security system or to change button assignments if desired. In order to enter Learn Routine, the Valet/Program push button must be plugged into the main brain's Blue 2 Pin Port (Look for a small black push button located under the drivers dash or drivers kick panel somewhere). The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to remember whenever programming this unit. 1) Open a door and make sure the dome light is on. 2) Turn the ignition on to the RUN position or you may also start car. 3) Within 10 seconds, press and release the Valet/Program switch the number of times that corresponds to the desired channel (listed below). Once you have selected the channel, press the switch once more and HOLD it. The LED will flash and then the horn will chirp (if connected) to confirm the selected channel. Do not release the Valet/Program switch. CHANNEL # FUNCTION 1 Arm / Disarm / Panic 2 Silent Mode / Remote Valet / Trunk Release 3 Remote Start or other accessories 4 Arm only (4 button remote) 5 Disarm only (4 button remote) 6 Panic only (4 button remote) 7 Auto Program single Arm – Disarm – Panic button configuration (4 button remote) 8 Auto Program this remote 9 Delete all transmitters CHANNEL 9: If any transmitter button from a known transmitter is programmed to channel 9, all transmitters will be erased from memory. This is useful in cases when one of the customer’s transmitters is lost or stolen. This will erase any lost or stolen transmitters from your system’s memory. It can also be used to start from scratch if the transmitter buttons were programmed incorrectly. 4) You can advance from programming one channel to another by releasing the Valet/Programming switch and tapping it to advance channels and then HOLDING it. For instance; you have programmed Channel 1 and you want to program Channel 2. Release the Valet/Program switch. Press it one time and release it to advance from Channel 1 to Channel 2. Now, press and HOLD the Valet/Program switch. The LED will flash 2 times and the horn will chirp twice (if connected). As before, do not release. If you want to program Channel 3 after programming Channel 1, release the Valet/Program switch, press it twice and release it to advance to Channel 3. Then press it once more and HOLD it. The horn will chirp 3 times (if connected) and the LED will flash 3 times to confirm it is ready to receive the code from the transmitter. 5) Once the code(s) are learned, the Valet/Program push button can be released. 6) Programming mode will be exited if one of the following actions occurs: a. Ignition key is turned to the OFF position b. Valet/Program switch is pressed too many times. c. More than 15 seconds elapses between programming steps. The horn will emit one long chirp when programming mode has been exited. Payment: We accept payment via PayPal or Credit Card. Please contact us via eBay messages for any questions concerning payments. Payment is expected within 5 days. PA SALES TAX: As per the State of PA Franchise Board we must collect sales tax from PA Residents for any purchase made from our store. Contact/Email: Due to scams etc, we DO NOT respond to emails. We only read/respond to EBAY MESSAGES. Messages & Best Offers are checked throughout the day & we typically respond 7 days a week. Please contact us with questions via eBay messages (keyless4u). 100% Guarantee Remote Shipping / Return Policy Warranty/Returns: 1. We have a 30 day return policy. 2. All returns for replacements and refund need an RMA #. 3. Please contact us before returning items so we can give you the RMA # and the proper return address. 4. No refunds / replacements will be granted without an RMA# We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged. Please Note: Each remote and circuit board is UV id’d prior to shipment – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement. Does this keyless remote entry come with a battery? Yes. It will have a working battery installed. Battery Condition: A. All remotes sold on Keyless4u include working batteries. B. Installed batteries are not tested for battery life- they are simply working. Some are new and some are used. Your vehicle will be installed with one of the following keyless entry systems: a. Standard Keyless Remote Packages: Installed at time of manufacture. b. Optional Keyless Remote Packages: Installed by a dealer. c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop. d. No remote keyless entry system at all. The above information can change which remote you need for your installed remote keyless system. . . . Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items. . . . . . . . . . . . . . . . .

Price: 28.94 USD

Location: Wellsboro, Pennsylvania

End Time: 2024-08-16T12:32:43.000Z

Shipping Cost: 6.96 USD