Wish Pearl

XPA-3 Gen3 3 Channel Audiophile Home Theater Power Amplifier

Description: Used lightly over the time had. Moving and looking to upgrade. Well taken care of, have all original parts and packaging. Circuit TopologyThe XPA-3 Gen3 is a fully modular audio power amplifier with a high-efficiency switch mode power supply (SMPS), independent, fully discrete, dual differential, high current, short signal path Class A/B amplifier modules, Optimized Class H™ power supply topology, and microprocessor-controlled fault protection.The XPA-3 is powered by a high efficiency, audiophile grade, Switch Mode Power Supply (SMPS).Audio SpecificationsThe XPA-3 Gen3 features three of our High-Powered Single Channel Modules. Audio Specifications (Three High-Powered Single Channel Modules):Power Output:• 300 watts RMS/channel; 20 Hz – 20 kHz; THD<0.1%; 8 Ohms; one channel driven• 550 watts RMS/channel; 20 Hz – 20 kHz; THD<0.2%; 4 Ohms; one channel driven• 300 watts RMS/channel; THD<0.1%; 8 Ohms; two channels driven• 490 watts RMS/channel; THD<0.1%; 4 Ohms; two channels driven• 275 watts RMS/channel; THD<0.1%; 8 Ohms; ALL THREE channels drivenPower Bandwidth (at rated power; 4 Ohm - 8 Ohm load): 20 Hz to 20 kHz (+ / – 0.1 dB)Broad Band Frequency Response: 5 Hz to 80 kHz +0/-2 dBTHD + noise: < 0.005%; at 100 watts RMS; 1 kHz; 8 OhmsSignal to Noise Ratio (8 Ohm load):• > 117 dB; ref FTC rated power; unbalanced input (A-weighted)• > 91 dB; ref 1 watt; unbalanced input (A-weighted)Minimum Recommended Load Impedance (per channel): 4 Ohms (one 4 Ohm load or two paralleled 8 Ohm loads).Damping Factor (8 Ohm load): > 500Input Sensitivity (for rated power; 8 Ohm load): 1.5 VGain: 29 dBMaximum Power Consumption: 1,400 watts.Note: The values shown refer to the amount of power the amplifier would consume while playing test tones continuously, on all channels, at full power, into a load bank. Therefore, they are not at all characteristic of what you would expect when playing music or the soundtrack from a movie. Normal audio signals are dynamic, so the amount of power they require from second to second varies widely, and the average is far lower than this. With normal content, even playing very loudly, one of our amplifiers will consume far less power than indicated in the chart, so these values should not be considered a circuit requirement for normal operation. Input Impedance:• 33 kOhms (balanced)• 23.5 kOhms (unbalanced)Input And Output ConnectionsInput Connections (High-Powered Single Channel Modules): Unbalanced (RCA); balanced (XLR); one each per channel, independently selectable.Input Connections (Stereo Modules):2 Unbalanced (RCA); 2 balanced (XLR); two per channel, independently selectable.Speaker Output Connections: Audiophile grade, gold plated, 5-way binding posts.Trigger:• Trigger Input: 5 – 12 V (AC or DC); <10 mA input current required.• Trigger Output: 12 VDC; can drive any load up to 120 mA.Power RequirementsBetween 100 VAC and 250 VAC @ 50 / 60 Hz (automatically detected).Front Panel Controls and Indicators• Standby: push button (halo ring changes color to indicate Standby or On).• Status LEDs: one per channel; blue• Status LEDs change to red to indicate a fault conditionRear Panel Controls• AC Power switch: rocker switch (switches AC main power)• Status LEDs switch: disables front panel Status LEDs and dims Standby button halo.• Input selector switches (one per channel): metal toggle switches; select between balanced and unbalanced inputs.• Circuit Breaker: press button to reset circuit breaker.ProtectionThe XPA Gen3 is protected against excessive operating temperature, shorted speaker connections, ground faults, and other common fault conditions.MechanicalDimensions:• 17” wide x 8” high x 19” deep (unboxed; including feet)• 17” wide x 7” high x 19” deep (unboxed; without feet)• 24-1/2” wide x 12” high x 24-3/4” deep (boxed)Weight:• 39 lbs (unboxed)• 44 lbs (boxed)

Price: 1100 USD

Location: Jasper, Texas

End Time: 2024-10-21T14:53:02.000Z

Shipping Cost: N/A USD

Product Images

XPA-3 Gen3 3 Channel Audiophile Home Theater Power AmplifierXPA-3 Gen3 3 Channel Audiophile Home Theater Power AmplifierXPA-3 Gen3 3 Channel Audiophile Home Theater Power AmplifierXPA-3 Gen3 3 Channel Audiophile Home Theater Power AmplifierXPA-3 Gen3 3 Channel Audiophile Home Theater Power AmplifierXPA-3 Gen3 3 Channel Audiophile Home Theater Power AmplifierXPA-3 Gen3 3 Channel Audiophile Home Theater Power AmplifierXPA-3 Gen3 3 Channel Audiophile Home Theater Power Amplifier

Item Specifics

All returns accepted: ReturnsNotAccepted

Brand: Emotiva

Type: Power Amplifier

Audio Inputs: Stereo L/R RCA, XLR

Number of Channels: 3

Number of Inputs: 3

Color: Black

Model: XPA-3

Unit Quantity: 1

Recommended

2-Prong Power Cord for Emotiva UPA-1, UPA-7, UPA-200, UPA-700 Stereo Power Amps
2-Prong Power Cord for Emotiva UPA-1, UPA-7, UPA-200, UPA-700 Stereo Power Amps

$12.88

View Details
Emotiva BasX LCR Speakers - New, Sealed, Multiple Available
Emotiva BasX LCR Speakers - New, Sealed, Multiple Available

$125.00

View Details
EMOTIVA REFERENCE ERD-1 BI-POLE/DI-POLE SURROUNDS (1PR/BLK, WALL BRKTS) - XCLNT+
EMOTIVA REFERENCE ERD-1 BI-POLE/DI-POLE SURROUNDS (1PR/BLK, WALL BRKTS) - XCLNT+

$500.00

View Details
Emotiva basx TA-100
Emotiva basx TA-100

$485.00

View Details
Emotiva UMC-1 Preamplifier Processor HDMI Home Theater AS IS / FOR PARTS
Emotiva UMC-1 Preamplifier Processor HDMI Home Theater AS IS / FOR PARTS

$149.97

View Details
6ft 2-Prong Power Cord for Emotiva Airmotiv 4s 5s 6 Powered Studio Monitors
6ft 2-Prong Power Cord for Emotiva Airmotiv 4s 5s 6 Powered Studio Monitors

$12.88

View Details
Emotiva XPA 2 Gen3 power amp
Emotiva XPA 2 Gen3 power amp

$740.69

View Details
Emotiva Processor RMC-1L
Emotiva Processor RMC-1L

$2900.00

View Details
Emotiva xmc-1 Gen2 7.2 Channel Pre-Amplifier Processor Remote Box New Bundle
Emotiva xmc-1 Gen2 7.2 Channel Pre-Amplifier Processor Remote Box New Bundle

$1199.99

View Details
EMOTIVA XDA-1 DAC Processor - Tested & Working!
EMOTIVA XDA-1 DAC Processor - Tested & Working!

$245.00

View Details